엔지니어에게 물어보세요
10월 16, 2026

일반적인 유압 씰 재질: NBR, HNBR, FKM, EPDM, PU 및 PTFE

일반적인 유압 씰 재질을 비교하고, 화합물 성분, 유체 호환성, 온도 및 씰 형상을 반드시 종합적으로 검토해야 하는 이유를 알아보세요.

엔지니어에게 물어보세요 견적 요청하기
Common hydraulic seal material samples beside a cylinder gland

Common hydraulic seal materials include nitrile rubber (NBR), hydrogenated nitrile (HNBR), fluoroelastomer (FKM), EPDM, polyurethane (PU), and PTFE-based compounds. They are used for different sealing tasks and operating conditions. No one family is the best choice for every cylinder, and a material name alone is not a complete specification.

The practical question is whether a particular compound, in a particular seal profile, suits the actual fluid, temperature, pressure, motion, and housing. The complete assembly may contain more than one material. This guide compares the families at a basic level and explains how to prepare a reviewable material request without converting general compatibility information into an unsupported guarantee of service life.

목차
  1. A material family is not a compound specification
  2. Common material families and their roles
  3. Compatibility starts with the actual fluid
  4. Temperature ratings need context
  5. PTFE assemblies include more than the sliding ring
  6. A material substitution example
  7. Questions about seal materials

A material family is not a compound specification

NBR identifies a polymer family. A supplier's compound code identifies a more specific formulation. Hardness, fillers, processing, and other formulation choices can change behaviour within that family.

This distinction matters when purchasing an apparently equivalent seal. “Same material” might mean only that both products are described as nitrile, not that their compounds or performance are equivalent. A complete designation should connect the material to the intended seal profile and product documentation.

Colour is not a universal identification method. A manufacturer may use it consistently within a range, but another supplier can use the same colour for a different material. Keep traceable packaging and part records.

The point also applies to a static O-ring: a familiar shape and nominal size do not remove the need to identify the compound.

Seal material family compared with a complete compound specification
Seal material family compared with a complete compound specification, illustrating the section “A material family is not a compound specification”.

Common material families and their roles

The following table is a starting map, not an approval chart or a temperature-rating table.

FamilyCommon reason it is consideredImportant review boundary
NBROil-compatible elastomer options for seals and energizersActual fluid, temperature, and environmental exposure
HNBRElastomer options where heat or oxidative resistance motivates further reviewSpecific formulation and cold-performance requirements
FKMOptions for elevated-temperature or chemical-resistance requirementsFluid identity and low-temperature behaviour
EPDMOptions for selected water-based or other compatible mediaGenerally unsuitable for conventional mineral-oil service
PUDynamic profiles where wear and mechanical resistance are importantSpecific grade, water exposure, temperature, and fluid
PTFE-based compoundsSliding elements where friction and chemical behaviour are importantFiller, support geometry, and energizer compatibility

Hallite's elastomer overview identifies the main rubber families, while its materials guide illustrates the broader variety of sealing and bearing materials.

HNBR is produced by hydrogenating nitrile rubber. Parker's HNBR technical bulletin discusses its resistance characteristics in specific compounds. That does not make HNBR a drop-in replacement for every NBR seal.

Treat EPDM particularly carefully in an oil-cylinder enquiry. Hallite's fluid compatibility chart marks its listed EPDM compounds unsuitable for the listed mineral hydraulic oils. A recommendation for water service cannot be transferred to mineral oil simply because both fluids pass through a hydraulic system.

Common hydraulic seal material families and typical roles
Common hydraulic seal material families and typical roles, illustrating the section “Common material families and their roles”.

Compatibility starts with the actual fluid

Record the fluid's manufacturer and product name, not just its broad category. Include known mixtures, additives, contamination, and cleaning chemicals that can contact the seal. A change of fluid can alter the material requirement even if cylinder pressure remains unchanged.

A compatibility chart is useful for screening out poor candidates and identifying questions. It is not a complete prediction of dynamic sealing performance. Trelleborg's material compatibility resource provides a starting point for that screening, but application-specific confirmation is still needed.

Separate chemical compatibility from mechanical suitability. A material can resist a fluid yet perform poorly in a profile or clearance arrangement that was designed for something else.

For polyurethane, ask about the particular grade's suitability for water exposure and hydrolysis-related conditions rather than assuming every PU formulation behaves alike. Do not substitute a general polymer family statement for the supplier's documented recommendation.

Inputs for checking hydraulic seal material compatibility
Inputs for checking hydraulic seal material compatibility, illustrating the section “Compatibility starts with the actual fluid”.

Temperature ratings need context

A temperature range needs an identified compound and exposure condition. Continuous operation, brief peaks, ambient storage, and cold starting are different questions. A quoted upper limit does not describe all of them.

At low temperature, the ability of a seal to recover and follow movement can matter, especially when pressure or motion changes. A ring that seals in a stationary check may behave differently during cold operation. Ask which duty the supplier's data actually cover.

At high temperature, consider the fluid, dwell time, and complete assembly. Avoid combining a material's highest advertised temperature with a seal profile's highest advertised pressure and speed unless that combination is supported.

Temperature at the seal contact may also differ from a reservoir reading. The review should state where measurements were taken and which temperatures remain estimates. This is more useful than choosing a material by a single number on a comparison chart.

PTFE assemblies include more than the sliding ring

A PTFE-based sealing element may be paired with an elastomer energizer or another loading arrangement. In such a design, the sliding material and the energizer have separate compatibility requirements.

Parker's PTFE materials resource discusses filler selection and its tradeoffs. “PTFE” therefore does not imply that every filled compound has identical wear, mechanical, or counter-surface behaviour.

Consider the complete piston seal assembly. A suitable sliding ring does not protect an unsuitable energizer from the fluid or temperature it experiences. Back-up components and adjacent guides may also introduce additional materials.

Do not assume that a low-friction material can use the same housing as an elastomer profile. Material choice, geometry, support, and installation requirements form a combined decision.

Likewise, a 가이드 링 has a bearing task. Its material assessment should not be copied directly from the pressure seal beside it.

Materials in a complete energized PTFE seal assembly
Materials in a complete energized PTFE seal assembly, illustrating the section “PTFE assemblies include more than the sliding ring”.

A material substitution example

Imagine a cylinder previously used with a documented mineral hydraulic oil. A proposed process change introduces a different fluid family and a higher cleaning temperature. The maintenance team asks for “the same seals, but in a better rubber.” This is an illustrative scenario.

The first step is to identify every affected material and its position. Include the rod seal, piston seal, static seals, energizers, and any other components exposed to the changed media. Replacing one visible ring may leave a less visible incompatible component behind.

Next document the new fluid product, expected mixture during changeover, operating and cleaning temperatures, motion duty, and available housing drawings. Ask the cylinder and seal suppliers to evaluate a complete configuration.

The resulting recommendation should identify compounds and profiles, assumptions, required changes, and the verification plan. A statement that the new material “resists chemicals” is too broad to close the review.

Purchasing should also retain the substitution record so that the next maintenance order does not revert to the old kit. The rod sealing system article explains why compatibility between neighbouring elements remains relevant even after individual material choices are made.

Questions about seal materials

Which material lasts longest?

There is no application-independent answer. Duty, profile, surfaces, contamination, installation, and the specific compound affect life. A material comparison without those conditions is incomplete.

Is FKM always better than NBR?

No. They offer different properties and compound options. A requirement that favours one property may introduce another limitation, particularly when fluid or low-temperature conditions differ.

Does PTFE mean the whole seal is chemically resistant?

No. Identify the filler and every energizing or supporting component. The complete assembly must suit the media and duty.

Can hardness alone identify an equivalent seal?

No. Hardness is one property, not a full formulation or performance specification. Even equal hardness within the same family does not prove interchangeability.

Prepare a material review with the current part identity, exact fluid, operating history, and housing details. Ask for the supplier's documented compound recommendation and the engineer's application approval, keeping any unresolved compatibility or testing questions visible.

관련 기사

이 유압 지식을 적용하는 데 도움이 필요하신가요?

도면, 사진, 작동 압력, 장비 세부 정보 또는 적용 관련 문의 사항을 보내 주십시오.

엔지니어에게 물어보세요 견적 요청하기