エンジニアに質問する
10月 15, 2026

O-Rings and Static Seals in Hydraulic Cylinders: Squeeze, Glands, and Back-up Rings

Understand O-rings and static seals in hydraulic cylinders, including squeeze, gland fill, pressure direction, back-up rings, and replacement checks.

エンジニアに質問する お見積り依頼
Hydraulic cylinder O-rings static seals and back-up ring

O-rings and static seals close leakage paths between hydraulic cylinder parts that are not intended to slide relative to one another. Examples may include a removable head-to-barrel joint or a piston-to-rod joint, depending on construction. An O-ring seals through its installed deformation and the way pressure acts on it within a correctly designed housing.

“Static” does not mean low pressure or constant pressure. The joint may experience repeated loading and temperature changes even though it has no intended sliding motion. Understanding the housing, material, pressure direction, and supporting components is therefore essential. This guide explains the basic terms without prescribing a universal groove size, compression percentage, or replacement material for every cylinder.

目次
  1. Static means no intended sliding
  2. How squeeze establishes the sealing contact
  3. Radial seals, face seals, and gland fill
  4. What back-up rings do
  5. Why a similar O-ring may not be equivalent
  6. Build the inspection and ordering record
  7. Static seal questions answered

Static means no intended sliding

A fixed joint can still deform slightly under load. Its sealing requirement depends on the movement and clearance the actual assembly permits, not just on whether two parts are bolted or threaded together.

The head and gland may contain both static and dynamic seals. A static seal at the head's outside diameter and a dynamic seal around the rod close different fluid paths. Identifying the location prevents a maintenance record from calling both simply “the gland seal.”

Some cylinder joints are welded and do not use an elastomer seal at that connection. Other joints use different static sealing forms. Do not infer the presence of an O-ring from a generic cylinder sketch.

Ports and fittings are another area where the sealing method must be identified separately. The oil port sealing arrangements article explains why thread appearance alone does not establish where the fluid seal is formed.

Examples of static seal locations in a hydraulic cylinder
Examples of static seal locations in a hydraulic cylinder, illustrating the section “Static means no intended sliding”.

How squeeze establishes the sealing contact

An O-ring's circular cross-section is deformed by its installed housing. That initial squeeze establishes contact before the full working pressure is applied. Pressure can then increase the loading against the relevant sealing surfaces.

Parker's O-ring handbook, sections 3.6 and 3.7, distinguishes squeeze from the volume occupied within the gland. These are related design checks, but they are not the same quantity.

Insufficient or excessive deformation can both be undesirable. The correct amount depends on the application, cross-section, material, tolerances, temperature, and fluid effects. A single percentage copied from an unrelated design should not become a universal shop rule.

The O-ring is also not an infinitely compressible filler. Its deformation needs space within a properly designed gland. Forcing a larger cross-section into an existing groove is a design change, even if it appears to stop an immediate leak.

Radial seals, face seals, and gland fill

Identify the direction of installed compression before selecting a design table.

Conceptその内容What it does not establish alone
Radial sealingCompression between generally cylindrical surfacesCorrect dimensions for every piston or head joint
Face or axial sealingCompression between facing surfacesSuitability for either internal or external pressure
SqueezeReduction of the ring's cross-section in the compression directionTotal available gland volume
Gland fillRing volume relative to the available cavityCorrect contact pressure or material compatibility

Pressure can act from different sides of a face seal. That affects how the ring is located and loaded, so “face seal” by itself is not a complete specification.

Parker's O-ring selector description explicitly separates radial and axial cases and connects material selection with size calculations. The tool description also identifies thermal expansion and fluid swelling as dimensional considerations. Using an engineering tool still requires correct input data and review of its assumptions.

In practice, record the housing case and dimensional basis before discussing whether an existing O-ring is “too small.” A stretched or permanently deformed old ring can be a poor reference for its original dimensions.

Difference between O-ring squeeze and gland fill
Difference between O-ring squeeze and gland fill, illustrating the section “Radial seals, face seals, and gland fill”.

What back-up rings do

A back-up ring supports the pressure seal at an extrusion clearance, as described in the Hallite back-up ring overview. It is not normally the primary fluid-sealing element. Its role becomes relevant when the O-ring could deform into a gap beyond the arrangement's intended capability.

For a conventional one-direction arrangement, support is placed on the lower-pressure side toward the potential extrusion gap. If pressure reverses, the design may need support for both directions. The actual number, orientation, and dimensions must follow the specified assembly. Parker illustrates the pressure–O-ring–back-up-ring order for a one-sided pressure case. Parker O-Ring Handbook, page 52.

This is a functional explanation, not permission to add a spare ring to any groove. A groove intended for an O-ring alone may not have space for a back-up ring while maintaining the required geometry.

Nor is a harder O-ring automatically equivalent to an O-ring plus a specified support element. Changing hardness can affect deformation and low-pressure behaviour as well as extrusion resistance. Review the complete joint before approving either change.

Conceptual support of an O-ring on the low pressure side
Conceptual support of an O-ring on the low pressure side, illustrating the section “What back-up rings do”.

Why a similar O-ring may not be equivalent

Consider an illustrative purchase request for a head seal. The old ring has been removed after service, and a nearby metric size appears to match it. The original drawing, however, identifies an inch-series size and a specific compound. The visual match is only a clue.

The reviewer needs the specified free dimensions, tolerances, material designation, and any required back-up components. Nominally close metric and inch sizes are not automatically interchangeable once the housing tolerance range is included.

Material identity is equally important. Two black rings with the same measured dimensions may have different compounds and hardness. A chemical compatibility claim for one material family does not prove that an untraceable replacement has the required formulation.

If the original designation is unavailable, state that explicitly and collect the housing and duty information for engineering identification. Do not convert uncertainty into certainty by assigning the nearest catalogue number without review.

その cylinder drawing is usually a better starting point than a worn ring's shape.

Identity information needed for a replacement static O-ring
Identity information needed for a replacement static O-ring, illustrating the section “Why a similar O-ring may not be equivalent”.

Build the inspection and ordering record

A useful record connects the part to the joint it seals. Include the cylinder identification, drawing revision, seal position, specified size system, compound, hardness designation where applicable, and the complete supporting-ring arrangement.

For operating conditions, provide fluid identity, temperatures, pressure directions, pressure cycling, and any known joint movement or damage. Keep normal duty separate from exceptional events.

During authorized inspection, compare the ring, housing, and mating surfaces together. Cuts, flattening, swelling, or edge damage can suggest questions for investigation, but each observation can have more than one explanation. Preserve the orientation and service history rather than treating a photograph as a complete failure analysis.

Assembly instructions should identify approved lubrication, cleanliness controls, and protection from sharp transitions where applicable. Do not infer those details from a generic O-ring article.

A leaking fixed joint should not be tightened experimentally while pressurized. Its mechanical retention and stored-energy conditions require the machine's service procedure. The goal of the record is to support that procedure, not replace it.

Static seal questions answered

Can a static seal experience changing pressure?

Yes. Static refers to the lack of intended relative sliding. Pressure cycles and small structural deformation may still affect its duty.

Are all O-rings static seals?

No. O-rings can also be used in specified dynamic or energizing roles. This article concerns static cylinder joints; those other applications require their own design conditions.

Should every O-ring have a back-up ring?

No. The need depends on the complete extrusion-risk assessment and housing design. Adding one without checking available space and pressure directions can make the assembly unsuitable.

Can sealant replace a missing O-ring?

Do not assume so. The joint was designed for a defined sealing method. Any alternative requires a specific engineering decision covering compatibility, geometry, serviceability, and the surrounding hydraulic system.

「」を使用してください seal types overview to keep static joints distinct from the moving piston and rod interfaces. Before ordering, establish the exact joint, size, compound, and supporting geometry; these details turn an approximate replacement request into a reviewable specification.

関連記事

この油圧に関する知識を応用する上で、お手伝いが必要ですか?

図面、写真、使用圧力、機器の詳細、または用途に関するご質問などをお送りください。.

エンジニアに質問する お見積り依頼